[ новости /+++ | форум | теги | ]

NAME

foo2zjs-wrapper - Convert Postscript into a ZJS printer stream
 

SYNOPSIS

DESCRIPTION

COMMAND LINE OPTIONS

Normal Options

-c

Print in color (else monochrome).

-C colormode

Color correction mode [0].

0 Best compromise
1 Photos (using m2300w CRDs)
2 Photos and text (using m2300w CRDs)
3 Graphics and text (using m2300w CRDs)
10 ICM color profile (using -G *.icm file)

-d duplex

Duplex code to send to printer [1].

1 off 2 long edge 3 short edge

-m media

Media code to send to printer [1].

Media 2300DL 2200DL
standard 1 1
transparency 2 2
envelope 257 na
letterhead 259 na
thick 261 4
postcard 262 na
labels 263 3

-p paper

Paper size code to send to printer [1].

1 letter 9 A4
5 legal 11 A5
7 executive 13 B5

-n copies

Number of copies [1].

-r xresxyres

Set device resolution in pixels/inch [1200x600].

-s source

Source (Input Slot) code to send to printer [7].

1 upper 4 manual
2 lower 7 auto

-2

Print in 2-up. Requires the psutils package.

-4

Print in 4-up. Requires the psutils package.

Printer Tweaking Options

-u xoffxyoff

Set the offset of the start of the printable region from the upper left corner, in pixels [varies with paper size]. The defaults should work on the 2200DL and 2300DL, and have not been tested on any other printers.

-l xoffxyoff

Set the offset of the end of the printable region from the lower right corner, in pixels [varies with paper size]. The defaults should work on the 2200DL and 2300DL, and have not been tested on any other printers.

-L mask

Send the logical clipping values from -u/-l in the ZjStream. foo2zjs-wrapper always runs Ghostscript with the ideal page dimensions, so that the scale of the image is correct, regardless whether or not the printer has unprintable regions. This option is used to move the position of the clipped image back to where it belongs on the page. The default is to send the amount which was clipped by -u and -l, and should be good in most cases.

0 don't send any logical clipping amounts
1 only send Y clipping amount
2 only send X clipping amount
3 send both X and Y clipping amounts

-P

Do not send START_PLANE codes on monochrome output. May be needed by some monochrome-only printers, such as the HP LaserJet 1000.

-X padlen

Add extra zero padding to the end of BID segments. The default is 16 bytes. Padding 16 bytes of zeroes is needed for older ZjStream printers, such as the Minolta 2200DL and HP LaserJet 1000, and seems harmless to newer ones, such as the Minolta 2300DL. So the default should be good for all cases.

-F firmware

Some printers (such as the HP LaserJet) need firmware to be downloaded to them after they are powered up or reset. This option will always prepend the contents of the file firmware to the job. COMPLETELY UNTESTED - LET ME KNOW IF THIS IS USEFUL.

Color Tweaking Options

-g gsopts

Additional options to pass to Ghostscript, such as -glq-dDITHERPPI=nnnrq, etc. This option may appear more than once.

-G profile.icm

Convert profile.icm to a Postscript color rendering dictionary (CRD) using foo2zjs-icc2ps and adjust the printer colors by using the Postscript setcolorrendering operator. (WORK IN PROGRESS).

-G gamma-file.ps

Prepend gamma-file.ps to the Postscript input to perform color correction using the setcolortransfer Postscript operator. For example, the file might contain:
{0.333 exp} {0.333 exp} {0.333 exp} {0.333 exp} setcolortransfer

Debugging Options

-S plane

Output just a single color plane from a color print and print it on the black plane. The default is to output all color planes.

1 Cyan
2 Magenta
3 Yellow
4 Black

-D level

Set Debug level [0].

EXAMPLES

foo2zjs-wrapper testpage.ps > testpage.zm
zjsdecode < testpage.zm
lpr -P raw testpage.zm

foo2zjs-wrapper -c testpage.ps > testpage.zc

FILES

SEE ALSO

AUTHOR

Index

NAME

SYNOPSIS

DESCRIPTION

COMMAND LINE OPTIONS

Normal Options

Printer Tweaking Options

Color Tweaking Options

Debugging Options

EXAMPLES

FILES

SEE ALSO

AUTHOR

Партнёры:

Хостинг: